OpenIPC · AKoo7 · Jun 24, 2026
@@ -60,6 +60,7 @@ jobs:
           - gk7202v300_lite_cootli_camv0103
           - gk7202v300_lite_ipg-g3-wr
           - gk7202v300_lite_xg521
+          - gk7205v200_lite_cpplus-cp-unc-ta21l2c
           - gk7205v200_lite_tiandy-tc-c321n
           - gk7205v200_lite_vixand-ipc-1
           - gk7205v200_lite_vixand-iph-5-4g

@@ -28,6 +28,7 @@ CMCC HDC-51 A5-V12       T21N         SC2235    RTL8189FTV_SDIO  NOR_16M   done
 CMCC HDC-51 A6-V10       T31L         JXF37     RTL8188FU_USB    NOR_16M   done
 CMCC HDC-51 A6-V11       T31L         SC2332    RTL8188FU_USB    NOR_16M   done
 Cootli CAMV0103          GK7202V300   SC223A    SSV6355_USB      NOR_8M    in progress
+CP Plus CP-UNC-TA21L2C   GK7205V200   SC223A    -                NOR_16M   video-ok, ir-cut-no, audio-no
 Emax Wyvern Link         SSC338Q      IMX415                     NOR_16M   done
 Foscam X5                SSC337DE     GC4653    RTL8188FU_USB    NOR_16M   done
 G.Craftsman GCA50        T31ZX        GC4653    -                NOR_16M   done

@@ -0,0 +1,38 @@
+![OpenIPC logo][logo]
+
+## OpenIPC Builder
+_Experimental system for building OpenIPC firmware for known devices_
+
+
+### Release notes for the device
+
+**CP Plus CP-UNC-TA21L2C** — Dahua-OEM 2 MP full-colour bullet/turret camera.
+
+| | |
+|---|---|
+| SoC | Goke **gk7205v200** (lite), ARM Cortex-A7 |
+| Sensor | SmartSens **SC223A** (chip-id `0xcb3e`), 2-lane MIPI, 1080p30 |
+| Flash | 16 MiB SPI-NOR (XM25QH128); built with the standard 8 MiB layout |
+| Wi-Fi | none (wired-only) |
+| Audio | present on the hardware; not wired up in this profile yet |
+
+#### Board specifics
+The SC223A on this board is on the SoC's **hardware I2C0**, routed to the
+**VI-RAW** pads (`0x112c0060/0x64`, func2) instead of the default mipi-sensor
+pads (`0x112c0030/0x34`, func1) that the SDK `board=demo` bring-up probes. The
+sensor also needs a 27 MHz MCLK (`0x120100f0 = 0x19`, div6); the SDK default
+`0x11` (div4) leaves it unresponsive. Both are handled in
+`general/overlay/etc/init.d/S71devmem`, which runs after `S70vendor`
+(`load_goke`) and before `S95majestic`. No kernel module is required — the
+stock `open_sensor_i2c` reaches the sensor over `/dev/i2c-0` once the pads are
+muxed. Sensor reset/enable is `GPIO8_7` (`SENSOR_RSTN`, func2).
+
+Verified on hardware: chip-id `0xcb3e` over HW I2C0, MIPI PHY lock at
+1920x1080 with zero error counters, majestic streams correct colour 1080p.
+
+#### TODO
+- Characterise and wire up the IR-cut / night-mode GPIOs.
+- Enable audio.
+
+
+[logo]: https://openipc.org/assets/openipc-logo-black.svg
@@ -0,0 +1,66 @@
+# Architecture
+BR2_arm=y
+BR2_cortex_a7=y
+BR2_ARM_EABI=y
+BR2_ARM_FPU_NEON_VFPV4=y
+BR2_ARM_INSTRUCTIONS_THUMB2=y
+
+# Toolchain
+BR2_TOOLCHAIN_EXTERNAL=y
+BR2_TOOLCHAIN_EXTERNAL_DOWNLOAD=y
+BR2_TOOLCHAIN_EXTERNAL_URL="https://github.com/openipc/firmware/releases/download/$(OPENIPC_TOOLCHAIN).tgz"
+BR2_TOOLCHAIN_EXTERNAL_CUSTOM_PREFIX="arm-openipc-linux-musleabi"
+BR2_TOOLCHAIN_EXTERNAL_HEADERS_4_9=y
+BR2_TOOLCHAIN_EXTERNAL_CUSTOM_MUSL=y
+BR2_TOOLCHAIN_EXTERNAL_CXX=y
+
+# Kernel
+BR2_LINUX_KERNEL=y
+BR2_LINUX_KERNEL_CUSTOM_TARBALL=y
+BR2_LINUX_KERNEL_CUSTOM_TARBALL_LOCATION="https://github.com/openipc/linux/archive/$(OPENIPC_KERNEL).tar.gz"
+BR2_LINUX_KERNEL_USE_CUSTOM_CONFIG=y
+BR2_LINUX_KERNEL_CUSTOM_CONFIG_FILE="$(EXTERNAL_VENDOR)/board/$(OPENIPC_SOC_FAMILY)/gk7205v200.generic.config"
+BR2_LINUX_KERNEL_UIMAGE=y
+BR2_LINUX_KERNEL_XZ=y
+
+# Filesystem
+BR2_PACKAGE_BUSYBOX_CONFIG="$(BR2_EXTERNAL)/package/busybox/busybox.config"
+BR2_PACKAGE_UBOOT_TOOLS=y
+BR2_PACKAGE_ZLIB=y
+# BR2_PACKAGE_IFUPDOWN_SCRIPTS is not set
+BR2_PACKAGE_MOSQUITTO=y
+# BR2_PACKAGE_MOSQUITTO_BROKER is not set
+BR2_PACKAGE_WIREGUARD_LINUX_COMPAT=y
+BR2_PACKAGE_WIREGUARD_TOOLS=y
+BR2_TARGET_ROOTFS_CPIO=y
+BR2_TARGET_ROOTFS_SQUASHFS=y
+BR2_TARGET_ROOTFS_SQUASHFS4_XZ=y
+
+# OpenIPC
+BR2_OPENIPC_SOC_VENDOR="goke"
+BR2_OPENIPC_SOC_MODEL="gk7205v200"
+BR2_OPENIPC_SOC_FAMILY="gk7205v200"
+BR2_OPENIPC_VARIANT="lite"
+BR2_OPENIPC_FLASH_SIZE="8"
+
+# Packages
+BR2_PACKAGE_DROPBEAR_OPENIPC=y
+BR2_PACKAGE_GOKE_OSDRV_GK7205V200=y
+BR2_PACKAGE_HISILICON_OPENSDK=y
+BR2_PACKAGE_IPCTOOL=y
+BR2_PACKAGE_JSONFILTER=y
+BR2_PACKAGE_LIBCURL_OPENIPC=y
+BR2_PACKAGE_LIBCURL_OPENIPC_CURL=y
+# BR2_PACKAGE_LIBCURL_OPENIPC_PROXY_SUPPORT is not set
+# BR2_PACKAGE_LIBCURL_OPENIPC_COOKIES_SUPPORT is not set
+# BR2_PACKAGE_LIBCURL_OPENIPC_EXTRA_PROTOCOLS_FEATURES is not set
+BR2_PACKAGE_LIBEVENT_OPENIPC=y
+BR2_PACKAGE_LIBOGG_OPENIPC=y
+BR2_PACKAGE_MAJESTIC_FONTS=y
+BR2_PACKAGE_MAJESTIC_WEBUI=y
+BR2_PACKAGE_MAJESTIC=y
+BR2_PACKAGE_MBEDTLS_OPENIPC=y
+BR2_PACKAGE_OPUS_OPENIPC=y
+BR2_PACKAGE_OPUS_OPENIPC_FIXED_POINT=y
+BR2_PACKAGE_VTUND_OPENIPC=y
+BR2_PACKAGE_YAML_CLI=y
@@ -0,0 +1,31 @@
+#!/bin/sh
+#
+# CP Plus CP-UNC-TA21L2C (Goke gk7205v200, SmartSens SC223A) board pinmux.
+#
+# Runs after S70vendor (load_goke), overriding the SDK board=demo defaults
+# for this board's actual wiring:
+#  - the SC223A i2c is on hardware I2C0 routed to the VI-RAW pads
+#    (0x60/0x64 func2), not the default mipi-sensor pads (0x30/0x34 func1);
+#  - sensor reset/enable is GPIO8_7 (SENSOR_RSTN, func2);
+#  - the SC223A needs a 27 MHz MCLK (div6 = 0x19); the SDK default 0x11
+#    (div4) is wrong, so the sensor never ACKs without this.
+# (load_goke already muxes SENSOR_CLK 0x112c0028 to func1, so it is left as-is.)
+#
+case "$1" in
+	start)
+		devmem 0x112c0030 32 0x0     # default I2C0 SDA -> GPIO (de-mux)
+		devmem 0x112c0034 32 0x0     # default I2C0 SCL -> GPIO (de-mux)
+		devmem 0x112c0060 32 0x2     # GPIO7_2 -> I2C0_SDA (func2, VI-RAW)
+		devmem 0x112c0064 32 0x2     # GPIO7_3 -> I2C0_SCL (func2, VI-RAW)
+		devmem 0x112c0048 32 0x2     # GPIO8_7 -> SENSOR_RSTN (func2)
+		devmem 0x120100f0 32 0x19    # sensor MCLK = 27 MHz (div6)
+		;;
+
+	stop)
+		;;
+
+	*)
+		echo "Usage: $0 {start}"
+		exit 1
+		;;
+esac
@@ -0,0 +1,33 @@
+#!/bin/sh
+#
+# Perform basic settings on a known IP camera
+#
+#
+# Set sensor
+#
+fw_setenv sensor sc223a
+#
+# Set custom upgrade url
+#
+fw_setenv upgrade 'https://github.com/OpenIPC/builder/releases/download/latest/gk7205v200_lite_cpplus-cp-unc-ta21l2c-nor.tgz'
+#
+#
+# Set custom majestic settings
+#
+cli -s .system.maxFps 30
+cli -s .video0.fps 30
+cli -s .video0.codec h265
+cli -s .osd.enabled true
+cli -s .osd.template "OpenIPC | %F %T %Z"
+#
+# Night mode / IR-cut and audio: the GPIO pins for the IR-cut filter and
+# IR LEDs on this board are not characterised yet, so they are left at
+# defaults (TODO).
+#
+#
+# This device is wired-only (no wlan).
+#
+adduser viewer -s /bin/false -D -H
+echo viewer:123456 | chpasswd
+#
+exit 0
@@ -0,0 +1,47 @@
+/etc/sensors/60fps/720p_imx307_i2c_2l.ini
+/etc/sensors/WDR/5M_imx335.ini
+/etc/sensors/WDR/imx335_i2c_4M.ini
+/etc/sensors/4l_sc223a_i2c_1080p.ini
+/etc/sensors/5M_imx335.ini
+/etc/sensors/bt656_720p.ini
+/etc/sensors/gc1054_i2c_720p.ini
+/etc/sensors/gc2053_i2c_1080p.ini
+/etc/sensors/gc4023_i2c_4M.ini
+/etc/sensors/gc4653_i2c_4M.ini
+/etc/sensors/gc5603_i2c_5M.ini
+/etc/sensors/imx307_i2c_2l_1080p.ini
+/etc/sensors/imx335_i2c_4M.ini
+/etc/sensors/jxf23_i2c_1080p.ini
+/etc/sensors/jxf23_i2c_dc_1080p.ini
+/etc/sensors/sc200ai_i2c_1080p.ini
+/etc/sensors/sc2232h_i2c_1080p.ini
+/etc/sensors/sc2239_i2c_1080p.ini
+/etc/sensors/sc2335_i2c_1080p.ini
+/etc/sensors/smtsec_imx307_i2c_4l_1080p.ini
+/etc/sensors/jxh63_i2c_720p.ini
+#
+/etc/sensors/iq/imx335.ini
+/etc/sensors/iq/sc2232.ini
+#
+/usr/lib/sensors/libsns_bt656.so
+/usr/lib/sensors/libsns_f23.so
+/usr/lib/sensors/libsns_f37.so
+/usr/lib/sensors/libsns_gc2053.so
+/usr/lib/sensors/libsns_gc4653_2l.so
+/usr/lib/sensors/libsns_imx307.so
+/usr/lib/sensors/libsns_imx307_2l.so
+/usr/lib/sensors/libsns_imx335.so
+/usr/lib/sensors/libsns_sc200ai.so
+/usr/lib/sensors/libsns_sc2239.so
+/usr/lib/sensors/libsns_sc223a_4l.so
+/usr/lib/sensors/libsns_sc2335.so
+/usr/lib/sensors/libsns_sc2232h.so
+/usr/lib/sensors/libsns_sc3235.so
+/usr/lib/sensors/libsns_sc3335.so
+/usr/lib/sensors/libsns_h63.so
+#
+/lib/modules/4.9.37/kernel/drivers/i2c/busses/i2c-tiny-usb.ko
+/lib/modules/4.9.37/kernel/drivers/scsi/scsi_mod.ko
+/lib/modules/4.9.37/kernel/drivers/scsi/scsi_transport_fc.ko
+/lib/modules/4.9.37/kernel/drivers/scsi/sd_mod.ko
+/lib/modules/4.9.37/kernel/fs/f2fs/f2fs.ko